RE: RES: mu SETUP

From: Bob Romprey (zoot@farts.com)
Date: Fri Dec 15 2000 - 07:17:55 CET

('binary' encoding is not supported, stored as-is) Try filling in the io and IRQ parameters when doing the setup with "" rather than the '' as suggested in the setup text.......I experienced the same problem today using a 3c509b card.........replaced '' with "" and it works just fine now.
the "" represents an empty string.

winsor

>Reply-To: mulinux@sunsite.auc.dk
>From: "J.Vieira" <vieirant@terra.com.br>
>To: <mulinux@sunsite.auc.dk>
>Subject: RES: mu SETUP
>Date: Fri, 15 Dec 2000 01:10:31 -0200
>
>Hello small World of MuLinux
>
>I get the same error "Symbol 'io' not found" trying to use my ne2k-pci on
>mu10r5
>
>I´ve already seem this film!!!
>
>Jose Vieira
>Linux User 100.600
>
>
>-----Mensagem original-----
>De: Jos? Luis G?mez Dans
>[mailto:jgomez@faust.champagne.sp.inova.com.br]Em nome de José Luis
>Gómez Dans
>Enviada em: quinta-feira, 14 de dezembro de 2000 15:15
>Para: mulinux@sunsite.auc.dk
>Assunto: Re: mu SETUP
>
>
>On Thu, Dec 14, 2000 at 07:06:40PM +0100, Christian Bourgeois wrote:
>> > If I well remember, it is based on a rtl8139 chip, so it should work
>with
>> > rtl8139 netword module.
>
> Note that this is a PCI card...
>
>> > But,
>> >
>> > when "setup eth0 CARD=rtl8139 IRQ=5 IO=0xE000 IP=192.168.0.203" i always
>> > get the error "Symbol 'io' not found" !!!
>> > I haven't figured out where the problem comes from.
>> >
>> > Before installing mulinux on the computer, I had tested it
>> > with floppy disks (with SRV only, not WKS), and it worked fine with that
>> > card. But is was not the last version, it was the 11r1 I think.
>
> There's no IO or IRQ for a PCI card. If you just do
>insmod rtl8139, you would be alright. I don't have mu at hand, but you
>don't what to have any IO or IRQ for thsi card
>
>> > I tested the above hard disk installation with the 10r5 and 11r2, and
>both
>> > give the same error.
>> >
>>
>> Do you have any idea ?
>> It'll be very helpfull, as I'm going to install it on about 25 computers
>!!!
>>
>> Also, is there any way to protect the "C:\LINUX" from being modified when
>in
>> DOS mode ?
>>
>> Thanks a lot,
>>
>> Cheers,
>> Christian.
>>
>>
>> ---------------------------------------------------------------------
>> To unsubscribe, e-mail: mulinux-unsubscribe@sunsite.auc.dk
>> For additional commands, e-mail: mulinux-help@sunsite.auc.dk
>
>--
>José L Gómez Dans PhD student
>Tel: +44 114 222 5582 Radar & Communications Group
>FAX; +44 870 132 2990 Department of Electronic Engineering
> University of Sheffield UK
>
>---------------------------------------------------------------------
>To unsubscribe, e-mail: mulinux-unsubscribe@sunsite.auc.dk
>For additional commands, e-mail: mulinux-help@sunsite.auc.dk
>
>
>
>---------------------------------------------------------------------
>To unsubscribe, e-mail: mulinux-unsubscribe@sunsite.auc.dk
>For additional commands, e-mail: mulinux-help@sunsite.auc.dk

------------------------------------------------------------
Visit the world's greatest site at http://www.farts.com and listen to the fart
of the day. Also, get your very own farts.com E-mail account. FREE!!!!!

---------------------------------------------------------------------
To unsubscribe, e-mail: mulinux-unsubscribe@sunsite.auc.dk
For additional commands, e-mail: mulinux-help@sunsite.auc.dk

This archive was generated by hypermail 2.1.6 : Sat Feb 08 2003 - 15:27:17 CET